Additional Resources

We've found this post about A Step-by-Step Guide to Installing a Bathtub listed below on the net and concluded it made perfect sense to discuss it with you here.

Setting up a bathtub isn't specifically brain surgery, however it does call for strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old bathtub with a new one is additionally a moderately difficult job. If the old tub is readily obtainable, the job can relocate quickly; if you need to open a wall surface to remove the old tub and position the brand-new bath tub, the job is a lot harder. In either case, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old tub as well as set in the new one. See to it you have qualified yourself for the task and fit trying it. Instead of hiring a service provider to take control of a halfway-completed project, it is better to take into consideration using one prior to you begin. Chances are you might need an expert plumber to make tube links.
This article will assist you mount a new tub in your washroom if you have actually currently purchased a brand-new bathtub as well as don't require to transform the setup of your previous water supply pipes.
Your devices and also product list must consist of the following:

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Preparing for the Installment

First of all, the supporting structure provided with the bath should be fitted (if required) according to the supplier's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to make sure that if the tap features a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps system to avoid strain on the bathtub.
Fit the flexible tap adapters to the bottom of the two faucets making use of 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you use every one of the provided washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath must now be ready to be suited its last position.

Removing Old Touches

If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you should do is disconnect the supply of water. After doing so, turn on the taps to drain any type of water remaining in the system. The process of getting rid of the existing faucets can be fairly bothersome as a result of the limited gain access to that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the faucets. Have a towel ready for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been removed, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning during this process. Once the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Prior to proceeding to fit the new taps, contrast the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.

Setting up the Bathtub

Utilizing both wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are valuable in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four tiny factors.
The next goal is to ensure that the tub is leveled all round. This can be achieved by inspecting the spirit level as well as readjusting the feet on the bath tub up until the level reviews level.
To set up taps, fit all-time low of the outermost adaptable faucet connector to the ideal supply pipe by making a compression join; then do the exact same for the other tap.
Activate the water supply and also examine all joints and also new pipework for leakages and tighten them if needed. Fill the bath tub and likewise check the overflow electrical outlet and the regular electrical outlet for leaks.
Lastly, fix the bath paneling as defined in the maker's instruction manual. Tiling as well as securing around the bathtub should wait until the bath tub has been used a minimum of once as this will certainly resolve it into its final position.

Fitting New Taps

If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washers remain in location between the tap as well as the sink. Safeguard the faucet in place with the maker provided backnut. When the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular tap ports. The previous type should be connected to the tap ends initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.

Tiling Around the Bathtub

In the area where the bathroom meets the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to split a stiff seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, bring about complications with wetness and possible leaks to the ceiling listed below.
You can select from a range of coloured sealers to blend in your components and fittings. They are offered in tubes and also cartridges, and also are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly load the tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in usage. The sealant can split rather very early if you do not think about this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the tiles utilizing water-resistant or water resistant sticky and cement.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

 

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

 

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

 

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

 

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

 

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

 

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

 

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

 

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

 

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

Do you like reading up on A Step-by-Step Guide to Installing a Bathtub? Leave a remark further down. We'd be pleased to hear your ideas about this page. We hope that you visit us again before long. Sharing is nice. You just don't know, you might be helping someone out. Many thanks for your time. Come back soon.

Leak detection needed?